Just How to Set up a Tub: Install an Acrylic Tub and Bathtub Surround
Just How to Set up a Tub: Install an Acrylic Tub and Bathtub Surround
Blog Article
They are making a few good pointers relating to Tools You Need to Install a New Bathtub in general in this post down the page.
Mounting a tub isn't exactly brain surgery, however it does require strong plumbing, carpentry, and also often, tiling skills. Changing an old bath tub with a brand-new one is also a reasonably tough project. If the old bathtub is easily accessible, the job can move easily; if you have to open up a wall to get rid of the old tub and also position the brand-new bathtub, the job is much harder. In either instance, the job is within a residence handyman's abilities, although you will require a helper to move out the old bathtub as well as set in the brand-new one. Ensure you have qualified on your own for the task and fit attempting it. As opposed to employing a professional to take control of a halfway-completed project, it is far better to think about employing one prior to you begin. Opportunities are you might need a specialist plumber to make tube links.
This short article will certainly assist you mount a new bathtub in your shower room if you have actually already acquired a new bathtub as well as don't require to change the plan of your previous water supply pipelines.
Your tools as well as product checklist must comprise the following:
Preparing for the Setup
To start with, the supporting structure supplied with the bathroom must be fitted (if called for) according to the supplier's instructions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is important to ensure that if the faucet features a plastic washing machine, it is fitted between the bath and the taps. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the taps device to prevent pressure on the bath tub.
Fit the versatile tap adapters to the bottom of both taps using 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet with the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you use all of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath should now prepare to be suited its final position.
Removing Old Touches
If you require to replace old taps with brand-new ones as a part of your installment, then the first thing you ought to do is disconnect the water. After doing so, activate the faucets to drain any water continuing to be in the system. The process of getting rid of the existing taps can be quite troublesome due to the limited access that is often the situation.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a fabric all set for the staying water that will certainly come from the pipelines. Once the supply pipes have actually been eliminated, make use of the same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from turning throughout this process. When the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old securing compound.
Prior to going on to fit the new taps, compare the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Setting up the Tub
Using both wood boards under its feet, put the bathtub in the needed position. The wood boards are practical in evenly spreading out the weight of the tub over the location of the boards as opposed to focusing all the weight onto 4 little points.
The following objective is to make certain that the bath tub is leveled all round. This can be accomplished by examining the level and also readjusting the feet on the bath tub till the level checks out level.
To set up taps, fit the bottom of the furthest flexible faucet port to the suitable supply pipe by making a compression join; after that do the very same for the various other tap.
Turn on the supply of water and check all joints and brand-new pipework for leaks and tighten them if required. Fill the bathtub and also check the overflow outlet and the regular electrical outlet for leakages.
Finally, take care of the bath paneling as explained in the maker's user's manual. Tiling and sealing around the bathtub ought to wait till the bath tub has actually been utilized at the very least when as this will certainly resolve it right into its final position.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will require a plastic connector to stop damages to the thread. One end of the port fits on the plastic tail of the tap and the other end supplies a link to the existing supply pipes.
If you need to fit a monobloc, then you will certainly call for decreasing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin guaranteeing that the washers are in place in between the tap and the sink. Secure the tap in position with the maker offered backnut. As soon as the faucet is safely in place, the supply pipes can be attached to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with typical tap adapters. The previous type ought to be connected to the faucet finishes first, tightening just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bath fulfills the ceramic tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the installation can move sufficient to crack an inflexible seal, causing the water to pass through the wall in between the bath as well as the tiling, leading to difficulties with moisture and feasible leaks to the ceiling below.
You can choose from a range of coloured sealers to blend in your fixtures and also installations. They are sold in tubes as well as cartridges, and also can sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of soaked paper or soft rope. Bear in mind to always fill up the bath tub with water before sealing, to enable the activity experienced when the tub remains in usage. The sealant can break relatively very early if you do not think about this movement before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise conveniently readily available on the market. It is advisable to fit the tiles using water-resistant or water resistant adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I recently found that article on Tools You Need to Install a New Bathtub when doing a search on the web. So long as you enjoyed our post kindly do not forget to pass it around. I am grateful for your time. Please check our blog back soon.
Course Detail
Report this page